SF600Plus SPI NOR Flash Programmer
The SF600Plus is a high speed “in System Programming” programmer to update the SPI Flash soldered on board (In Circuit Programming) or in the socket adaptor (Off line programming). The programmer is easily controlled by the computer DediProg Software through the USB bus offering friendly interface and powerful features to users.
The SF600Plus combines the advantages of SF100 with additional improvements:- High speed USB – Higher SPI performances – Support Single, Dual and Quad IO (ISP mode only).
Features :
- USB High speed and high SPI performance, support up to 2Gb SPI Flash
- In-Circuit Programming: Program on board SPI Flash
- Off-line Programming: Program SPI Flash in the socket
- Start button feature: Able to Batch in the USB mode
- Standalone mode: Support Start button programming and IO Port programming.
- ISP Port supports 2 CS pins to program two Serial Flash memories
- Signal conflict protections
- Multi-Programmers Capability through USB
- Support 1.8V low voltage IC
- Support Windows 2003 and above
- Support both 32 and 64 bit OS
High performance (25MHz, Single IO)
*Please note the programming and verify time will depend on different IC type; please refer to the IC specification before programming.
Hardware
SF600SF600Plus is designed with ISP header, through an appropriate connector, users can connect the programmer and drive the SPI signals, supply the memory and control the controller or application status. Please refer to Table 1 for the SF600Plus 2×10 header pin out. DediProg also provides the SF600Plus ISP Cable which is used to connect the programmer to the 2X6 2.54mm ISP Pin Header on board, please refer to Table 2 for the SF600PlusISP Cable 2×6 pin out.
Table 1: SF600Plus ISP Header Pin Out (2×10)
| 1 | Vpp | CS2 | 2 |
| 3 | CS1 | Vcc | 4 |
| 5 | MISO/DQ1 | Hold/DQ3 | 6 |
| 7 | Wp/DQ2 | CLK | 8 |
| 9 | GND | MOSI/DQ0 | 10 |
| 11 | NC | Reset/IO3 | 12 |
| 13 | NC | NC | 14 |
| 15 | NC | NC | 16 |
| 17 | NC | NC | 18 |
| 19 | GPIO1 | GPIO2 | 20 |
Table 2: ISP Cable Connector Pin Out (2×6)
| 1 | Vpp | CS2 | 2 |
| 3 | CS1 | Vcc | 4 |
| 5 | MISO/DQ1 | Hold/DQ3 | 6 |
| 7 | Wp/DQ2 | CLK | 8 |
| 9 | GND | MOSI/DQ0 | 10 |
| 11 | NC | Reset | 12 |
The SF600Plus USB software tool chain offers high flexibility and fits the different and highest requirements:
Engineering Mode
For engineers and expert to access advanced features for development, repairing etc.
Production Mode
For operators in production to control multiple programmers and improve the throughput.
Command Line
Customer software can control multiple SF600 programmers by command line interface.
Hardware Requirement for ISP
To have a clear understanding on the different ISP or backup boot methods and different reference schematics, please download our dedicated application notes: AN0103 and AN0106
Standard Package
- SF600Plus Programmer x 1
- USB Cable x 1
- AC Power Adaptor (ME-SW-ADP-1) x 1
- ISP Cable (ISP-600-CB1-G) x 1
- SF100 2.54mm 2*4 ISP Cable (ISP1-CB) x 1
- SF600 Universal Adaptor (ADP-SF600-TO-SF100) x 1
Optional Purchase
- Backup Boot Flash Module-8N
- Backup Boot Flash Module-8W
- Backup Boot Flash Module-D8W
- Backup Boot Flash Module-DIP
- Backup Boot Flash Module-16W
- Backup Boot Flash Module QUAD-8W